Kepco MST 488 Programmer Manual do Utilizador descarregar pdf (Página 56)

B-8

MST 488-27 013004

B.28 STATus:QUEStionable[:EVENt]? QUERY

STAT:QUES?

Syntax: Short Form: STAT:QUES[EVEN]? Long Form: STATus:QUEStionable[EVENT]?

Return Value: <int_value> actual register value

Description: Indicates questionable events that occurred since previous STAT:QUES? query. Returns the

value of the Questionable Event register (see Table B-3). The Questionable Event register is a

read-only register which holds (latches) all events. Reading the Questionable Event register clears it.

(See example, Figure B-5.)

FIGURE B-5. USING STATUS COMMANDS AND QUERIES

TABLE B-3. QUESTIONABLE EVENT REGISTER, QUESTIONABLE CONDITION REGISTER

AND QUESTIONABLE CONDITION ENABLE REGISTER BITS

CONDITION PL OL RE NU NU NU NU NU OT NU CE VE

BIT 111098 76543210

VALUE204810245122561286432168421

PL POWER LOSS

OL OVERLOAD

RE RELAY ERROR

OT OVERTEMPERATURE

CE CURRENT ERROR

VE VOLTAGE ERROR

NU NOT USED

NOTE: The selected MST power supply is assumed to be operating in cV (constant voltage) mode.

STAT:OPER:ENAB 1056 Mask enabled for CC, WTG and bits.

STAT:OPER:ENAB? Returns 1056 (32 + 1024) (CC, WTG bits set).

STAT:QUES:ENAB 3 Mask enabled for OV and OC bits (1 + 2).

STAT:QUES:ENAB? Returns 3 (1 + 2) indicating OV and OC bits are enabled.

STAT:PRES Operation Condition and Questionable Condition registers are

reset.

INIT:CONT ON Continuous triggers enabled.

STAT:OPER:COND? Power supply returns 288 (256 + 32) to indicate that power

supply is constant voltage mode and Wait For Trigger is true.

STAT:OPER? Returns 1057, e.g., indicating that since the last reading of the

Operation Event Register the power supply has entered

Constant Current mode, the Wait Trigger was set.

STAT:OPER? Returns 0 indicating no changes since previous reading of the

Operation Event register.

STAT:QUES? Returns 0 (no questionable conditions occurred since previous

reading

--- OVERCURRENT CONDITION OCCURS

STAT:QUES? Returns 2 (overcurrent protection tripped since the last

STAT:QUES? query).

STAT:QUES:COND? Returns 2, (Power supply still in overcurrent protection state).

STAT:QUES? Returns 0, (Register cleared by previous STAT:QUES?).

STAT:QUES:COND? Returns 2, (Power supply still in overcurrent protection state).

SYST:ERR? Power supply returns 0,“No error” message.

inst:sel 1 Select instrument 1

stat:ques? MST 488 responds 4 indicating instrument 1 in current mode

inst:sel 2 Select instrument 2

stat:ques? MST 488 responds 8 indicating instrument 2 in voltage mode

stat:ques:inst:isum1? MST 488 responds 4 indicating instrument 1 in current mode

stat:ques:inst:isum2? MST 488 responds 8 indicating instrument 2 in voltage mode

1 2 ... 51 52 53 54 55 56 57 58 59 60 61 ... 67 68

Comentários a estes Manuais

Sem comentários

Kepco MST 488 Programmer Manual do Utilizador Página 56

Comentários a estes Manuais

Manuais e produtos relacionados com Fontes de alimentação Kepco MST 488 Programmer